Why Hot Water Runs Out Faster: Common Causes and Fixes Running out of hot water faster than normal is a frustrating problem—especially when it used to be fine. While the cause can be as simple as a setting change, it can also point to heating-element or thermostat failures, airflow issues, or hot-water piping problems that limit how quickly your system can supply warm water. Check the simplest causes first Many “hot water suddenly runs out” complaints start with changes in routine or system settings. If you recently increased the number/length of showers, added a dishwasher cycle, or started using multiple hot taps at once, the heater may be meeting demand but not keeping up. You should also verify the water heater temperature setting (commonly around 120°F/49°C for safety and efficiency). If it was accidentally turned down—or up causing rapid cycling—it can affect how long usable hot water lasts. Look ... Read more »
Zoeller Ejector Pump M-267 0.5HP
Description
May be used in those states where codes do not restrict solids size in effluent systems.
Features:
- Float operated, submersible (NEMA 6) 2-pole mechanical switch
- Durable cast construction, ASTM Class 25 cast iron, switch case and pump housing
- Cast iron base on models 267 and 268
- Engineered plastic base on model 266
- Non-Clogging Vortex Impeller Design. Engineered plastic impeller with metal inserts on models 266, 267 & 268 (1 PH).
- Not affected by materials normally found in drainage and sewage pumps
- Stainless steel screws, bolts, handle, guard and arm and seal assembly
- Neoprene square ring & gasket
- Oil-filled, hermetically sealed motor
- Oil lubricated bearings
- Carbon and ceramic shaft seal
- Passes 2" spherical solids
- 2" NPT discharge
- On point: 12" (automatic units); Off point: 4" (automatic units)
- Corrosion resistant powder coated epoxy finish
- Completely submersible
- Watertight and dust tight
- Automatic reset thermal overload protection (1 Phase only)
- Reserve powered design. For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.
Specs
| Type: | Automatic |
|---|---|
| Application: | Sewage Sewage Waste Transfer Effluent |
| Material: | Cast Iron |
| Horse Power: | 1/2 |
| Voltage: | 115V |
| Amperage: | 10.4 |
| Phase: | 1 |
| RPM: | 1725 |
| Cord Length: | 10' |
| Cord Type: | UL Listed, 3-Wire Neoprene Cord & Plug |
| Height: | 14-9/32" |
| Features: | w/ Plastic Impeller |
| Flow at 5 FT Head: | 128 GPM |
| Flow at 10 FT Head: | 89 GPM |
| Flow at 15 FT Head: | 50 GPM |
| Approvals: | UL/CSA |
| Weight (lbs): | 47.5 lbs |
| Discharge: | 2" |
| Solids Size: | 2" |
| Shutoff Head (ft.): | 21.5' |
Product Details
- Brand ZOELLER Manufacturer Part Number M267
- HP 1/2
- Rated Voltage 115V AC
- Phase - Pumps 1
- Amps 10.40
- Motor Type Hermetically-Sealed; Oil-Filled
- Body Material Cast Iron
- Impeller Material Thermoplastic
- Shaft Seal Material - Pumps Carbon; Ceramic
- Switch Actuation Vertical Float
- Switch Electrical Connection Integral
- On Point 12 in
- Off Point 5 in
- Flow Rate @ 10 Ft. of Head 85 gpm
- Flow Rate @ 15 Ft. of Head 45 gpm
- Flow Rate @ 20 Ft. of Head 10 gpm
- Max. Diameter Solids 2 in
- Min. Sump Pit Dia. 18 in
- Body Dia. 13-1/16 in
- Overall Height 14-9/32 in
- Cord Length 10 ft
- Discharge 2 in FNPT
- Max. Liquid Temp. 130 °F
- Max. Head 21.5 ft
- Duty Cycle Continuous
- Thermal Protection Yes
- RPM 1,725 RPM
- Agency Compliance CSA Certified; UL Listed
- Manufacturers Warranty Length 3 yr
- UNSPSC 40151517
- Country of Origin USA (subject to change)

Comments
Post a Comment